IEI Technology IceCare-10W series User Manual Download Page 48

Page: 48 / 107

ICECARE-10W Mobile Sales Assistant

Page 36

4.1 Available Software Drivers

NOTE:

The contents of the driver folder may vary throughout the life cycle of

the product and is subject to change without prior notice. Visit the IEI

website or contact technical support for the latest updates.

The following drivers can be installed on the system:



Chipset

driver



Graphics

driver



Audio

driver



Bluetooth

driver



Wireless LAN driver



RFID

driver

Connect the Utility CD came with the ICECARE-10W Series to the system and follow the

installation instructions given below to install the drivers.

4.2 Intel® Chipset Driver

To install the chipset driver, please follow the steps below.

Step 1:

Select

1.Chipset

from the list of the driver CD shown in

Figure 4-1.

Summary of Contents for IceCare-10W series












































































































Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands

IEI Technology IceCare-10W series, User Manual

Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands