IEI Technology IceCare-10W series User Manual Download Page 105

Page: 105 / 107

ICECARE-10W Mobile Sales Assistant

Page 93

E.1 Hazardous Materials Disclosure Table for IPB Products

Certified as RoHS Compliant Under 2002/95/EC Without
Mercury

The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the

presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances

would “not leak out or undergo abrupt change.” This product may contain replaceable

sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the table on the next page.

Summary of Contents for IceCare-10W series












































































































Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands

IEI Technology IceCare-10W series, User Manual

Search results

Summary of Contents for IceCare-10W series

Reviews:

Related manuals for IceCare-10W series

Brands by name

Popular brands