IEI Technology ICE-BT-T10-E38151 User Manual Download Page 74

Page: 74 / 97

ICE-BT-T10 COM Express Module

Page 64

6.4 Graphics Driver Installation

To install the graphics driver, please do the following.

Step 1:

Access the driver list. (See

Section 6.2

)

Step 2:

Click “

1-Bay Trail SOC

” and select the folder which corresponds to the

operating system.

NOTE:

The remainder of this installation assumes Windows 8 as the operating

system.

Step 3:

Unzip the file called

15.33.7.3366.zip

, and then locate the setup file and double

click on it to start the installation. If a 64-bit operating system is installed, please

unzip the 15.33.7.64.336.zip file to install the graphics driver.

NOTE:

To install graphics driver on a

32-bit

Windows 7 system, unzip

INTEL_EMGD.WIN7_PC_VERSION_36_15_0_1064.7Z.

To install graphics driver on a

64-bit

Windows 7 system, unzip

INTEL_EMGD.WIN7_BETA_VERSION_37_15_0_1055.7Z.

Step 4:

The

Welcome Screen

Figure 6-8

appears.

Step 5:

Click

Next

to continue.

Summary of Contents for ICE-BT-T10-E38151


































































































Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands

IEI Technology ICE-BT-T10-E38151, User Manual

Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands