manualshive.com logo in svg

IEI Technology HYPER-BW, User Manual

Share
Download
IEI Technology HYPER-BW User Manual Download Page 20

 

 

HYPER-BW 

Page  9 

1.7

 

Technical Specifications  

HYPER-BW technical specifications are listed below. 

Specification 

HYPER-BW 

SoC 

Intel® Pentium® N3710 on-board SoC (up to 2.56GHz, 
quad-core, 2MB cache, TDP=6W)   

Intel® Celeron® N3160 on-board SoC (up to 2.24GHz, 
quad-core, 2MB cache, TDP=6W)   

Intel® Celeron® N3060 on-board SoC (up to 2.48GHz, 
dual-core, 2MB cache, TDP=6W)   

Intel® Celeron® N3010 on-board SoC (up to 2.24GHz, 
dual-core, 2MB cache, TDP=4W) 

Intel® Celeron® x5-E8000

 on-board SoC (up to 2.00GHz, 

quad-core, 2MB cache, TDP=5W)

 

BIOS 

AMI UEFI BIOS

 

Memory 

One 204-pin 1333/1600 MHz single-channel DDR3L SDRAM 
unbuffered SO-DIMM slot support up to 8 GB 

Graphics  

Intel® HD Graphics Gen 8 Engine with 16 low-power 
execution units, supporting DX11.1, OpenGL 4.2 and 
OpenCL1.2 

Dis play Output 

Dual independent display   

2 x Mini HDMI (up to 3840x2160@30Hz) 

Ethernet 

LAN1: Realtek RTL8111 controller 

EC 

IT8587

 

Watchdog Timer 

Software programmable support 1~255 sec. system reset 

I/O Interface 

Audio Connector 

1 x HD Audio by 10-pin (2x5) header 

Ethernet 

One RJ-45 port 

Serial Ports  

1 x RS-232 (by pin header) 

Summary of Contents for HYPER-BW







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands