IEI Technology F15AD-H81i/PC-R10 User Manual Download Page 63

Page: 63 / 185

PPC-FxxA-H81 Panel PC

Page 48

Figure 3-37: Install into a Rack/Cabinet

Step 6:

Once the flat panel PC with the attached rack/cabinet bracket has been properly

inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to

the front of the rack or cabinet (

Figure 3-37

Step 0:

3.11.4 Arm Mounting

The PPC-FxxA-H81 is VESA (Video Electronics Standards Association) compliant and

can be mounted on an arm with a 100 mm interface pad. To mount the PPC-FxxA-H81 on

an arm, please follow the steps below.

Step 1:

The arm is a separately purchased item. Please correctly mount the arm onto

the surface it uses as a base. To do this, refer to the installation documentation

that came with the mounting arm.

NOTE:

When purchasing the arm please ensure that it is VESA compliant and

that the arm has a 100 mm interface pad. If the mounting arm is not VESA

compliant, it cannot be used to support the PPC-FxxA-H81 panel PC.

Summary of Contents for F15AD-H81i/PC-R10


























































































































































































Search results

Summary of Contents for F15AD-H81i/PC-R10

Reviews:

Brands by name

Popular brands

IEI Technology F15AD-H81i/PC-R10, User Manual

Search results

Summary of Contents for F15AD-H81i/PC-R10

Reviews:

Brands by name

Popular brands