IEI Technology eKINO-BT User Manual Download

Page: 90 / 157

eKINO-BT Mini-ITX SBC

Page 76

Step 2:

Plug the audio plugs into the audio jacks

. Plug the audio plugs into the audio

jacks. If the plugs on your speakers are different, an adapter will need to be used

to plug them into the audio jacks.

Line Out port (Lime):

Connects to a headphone or a speaker.

Microphone (Pink):

Connects to a microphone.

Figure 4-19: Audio Connector

Step 3:

Check audio clarity

. Check that the sound is coming through the right speakers

by adjusting the balance front to rear and left to right.

Step 0:

4.10.2 LAN Connection

There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection

to an external network. To connect a LAN cable with an RJ-45 connector, please follow

the instructions below.

Step 1:

Locate the RJ-45 connectors

. The locations of the RJ-45 connectors are

shown in

Chapter 3

Step 2:

Align the connectors.

Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the eKINO-BT. See

Figure 4-20

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands