manualshive.com logo in svg

IEI Technology eKINO-945GSE, User Manual, Page: 91 / 215

Share
Download
IEI Technology eKINO-945GSE User Manual Download Page 91

 

 

eKINO-945GSE Motherboard 

Page 75 

5.8 Chassis Installation 

5.8.1 Airflow 

 WARNING: 

Airflow is critical to the cooling of the CPU and other onboard 

components. The chassis in which the eKINO-945GSE must have air 

vents to allow cool air to move into the system and hot air to move out. 

The eKINO-945GSE must be installed in a chassis with ventilation holes on the sides 

allowing airflow to travel through the heat sink surface. In a system with an individual 

power supply unit, the cooling fan of a power supply can also help generate airflow 

through the board surface.   

 NOTE: 

IEI has a wide range of backplanes available. Please contact your 

eKINO-945GSE vendor, reseller or an IEI sales representative at 

3

[email protected]

 or visit the IEI website (

3

http://www.ieiworld.com.tw

) 

to find out more about the available chassis. 

5.8.2 Motherboard Installation 

To install the eKINO-945GSE motherboard into the chassis please refer to the reference 

material that came with the chassis. 

5.9 Internal Peripheral Device Connections 

The cables listed in 

8

Table 5-10

 are shipped with the eKINO-945GSE. 

Quantity 

Type 

1 

Keyboard and Mouse cable 

2 

SATA drive cable 

Summary of Contents for eKINO-945GSE
























































































































































































































Reviews:

No comments