IEI Technology eKINO-945GSE User Manual Download Page 177

Page: 177 / 215

eKINO-945GSE Motherboard

Page 161

8.2.2.2 Battery Detection

When the smart battery is connected to the AUPS series power module, the AUPS Battery

Status Monitor detects it and shows in the screen as

Figure 8-9

. Two batteries can be

connected to the AUPS series power module at the same time. The second battery

information is shown in the

Battery A Detection

section if connected.

Figure 8-9: Battery Detection

The battery is connected to the AUPS series.

Off

The battery is not connected to the AUPS series.

Full

The battery is fully charged.

Low

The battery is low.

Using

The battery is being used.

Charging

The battery is being charged.

Standby

The battery is fully charged and ready to be used anytime.

>60 C

The battery temperature is above 60°C.

<60 C

The battery temperature is below 60°C.

Table 8-1: Status Settings

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 177 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: