manualshive.com logo in svg

IEI Technology DM series, User Manual, Page: 83 / 128

Share
Download
IEI Technology DM series User Manual Download Page 83

 

 

DM Series Monitor 

Page 69

5.5.4 Wall Mounting 

 CAUTION: 

Due to safety concerns, it is highly recommended to use the VESA mounting 

kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit 

is purchased separately, please make sure the mounting kit is UL-listed. 

Each model of the DM series LCD monitor has four holes located on the rear panel for 

mounting the monitor to a wall. To mount the DM series LCD monitor onto a wall, please 

follow the steps below. 

Step 1: 

Select a location on the wall for the wall-mounting bracket.   

Step 2: 

Carefully mark the locations of the four bracket screw holes on the wall.   

Step 3: 

Drill four pilot holes at the marked locations on the wall for the bracket retention 

screws. 

Step 4: 

Align the wall-mounting bracket screw holes with the pilot holes. 

Step 5: 

Secure the mounting-bracket to the wall by inserting the retention screws into 

the four pilot holes and tightening them (

5

Figure 5-27

). 

 

Figure 5-27: Wall-mounting Bracket 

Summary of Contents for DM series

































































































































Reviews:

No comments