manualshive.com logo in svg

IEI Technology DM series, User Manual, Page: 69 / 128

Share
Download
IEI Technology DM series User Manual Download Page 69

 

 

DM Series Monitor 

Page 55

5.5   Mounting the Monitor 

The DM series LCD monitor can be mounted in a panel, cabinet, rack, DIN rail or wall. The 

monitor can also be mounted on a monitor arm or stand. The mounting methods are 

described below. 

 CAUTION: 

When mounting the monitor take care to tighten the retention screws or bolts 

until fully secure, but do not over tighten. Over tightening the retention screws 

or bolts may cause them to become stripped, rendering them useless. 

5.5.1 Panel Mounting 

Each model of the DM series LCD monitor has a series of mounting slots located on the 

top and bottom panel for mounting the monitor to a panel. 

 NOTE: 

The DM-65 monitor requires two special mounting brackets for installation into 

a panel. Refer to Section 

5

5.5.1.2 for details. 

5

Table 5-6 lists the number of mounting clamps required to mount the monitor to a panel. 

Model 

Mounting Clamps 

DM-190 14 

DM-170 10 

DM-150 10 

DM-121 10 

DM-104 10 

DM-84 8 

Table 5-6: Panel Mounting Clamps 

Summary of Contents for DM series

































































































































Reviews:

No comments