IEI Technology DM series User Manual Download Page 62

Page: 62 / 128

DM Series Monitor

Page 48

5.2.3 Packing List

All the monitors in the DM series are shipped with the following components:

1 x DM-190/170/150/121/104/84/65 series LCD monitor.

1 x AC power cable

1 x VGA cable

1 x 50W AC power adapter (DM-190 / 170 / 150)

1 x 36W AC power adapter (DM-121/ 104 / 84 / 65)

5 x Replacement round head screw

5 x Replacement flat head screw

5 x Replacement wire strain band

1 x User manual on CDROM

1 x Touch panel RS-232 cable

1 x Touch panel USB cable

1 x Touch Pen

1 x Driver CDROM

1 x Power cable for terminal block (Optional for M model)

If any of these items are missing or damaged, contact the distributor or sales

representative immediately.

5.3 Pre-installation Preparation

5.3.1 Tools

Before installing the DM series LCD monitor, make sure the following tools are on hand:

Philips (crosshead) screwdriver

: All the retention screws on the system are

Philips screws.

Soft working mat

: When the DM series LCD monitor is installed, the screen

is placed on the working surface. It is therefore important to rest the MPC

indutrial workstation on a soft at that cannot damage the LCD screen on the

front of the DM series LCD monitor.

Summary of Contents for DM series

































































































































Search results

Summary of Contents for DM series

Reviews:

IEI Technology DM series, User Manual, Page: 62 / 128

Search results

Summary of Contents for DM series

Reviews: