manualshive.com logo in svg

IEI Technology DM-F17A/PC-R31, User Manual, Page: 34 / 88

Share
Download
IEI Technology DM-F17A/PC-R31 User Manual Download Page 34

 

 

DM-F  S e rie s   Mo n ito r

 

P a g e   25 

PIN 

DESCRIPTION 

PIN 

DESCRIPTION 

PIN 

DESCRIPTION 

1 

RED 

6 

GROUND 

11 

NC 

2 

GREEN 

7 

GROUND 

12 

DDCDAT 

3 

BLUE 

8 

GROUND 

13 

HSYNC 

4 

NC 

9 

NC 

14 

VSYNC 

5 

GROUND 

10 

GROUND 

15 

DDCCLK 

Table 3-5: VGA Connector Pinouts 

 

Figure 3-9: VGA Connector 

 

3.4

 

Mo u n tin g   th e   Mo n ito r 

The DM-F  series  LCD  monitor can be mounted in a panel, cabinet, rack  or wall. The 

monitor can also be mounted on a monitor arm  or stand. The mounting methods are 

described below. 

  CAUTION: 

When mounting the monitor take care to tighten the retention screws or bolts 

until fully secure, but do not over tighten. Over tightening the retention screws 

or bolts may cause them to become stripped, rendering them useless. 

3.4.1

 

P a n e l  Mo u n tin g  

Each model of the DM-F series LCD monitor has a series of mounting slots located on the 

top and bottom panel for mounting the monitor to a panel. 

Table 3-

 

lists the number of mounting clamps required to mount the monitor to a panel. 

Summary of Contents for DM-F17A/PC-R31

























































































Reviews:

No comments