IEI Technology AFL-xxA-N270 series User Manual Download Page 114

Page: 114 / 171

AFL-xxA-N270 Series Panel PC

Page 99

BIOS Menu 18:North Bridge Chipset Configuration

Memory Hole [Disabled]

The

Memory Hole

reserves the memory space between 15MB and 16MB for ISA

expansion cards that require a specified area of memory to work properly. If an older ISA

expansion card is used, please refer to the documentation that came with the card to see if

it is necessary to reserve the space.

Disabled D

EFAULT

Memory is not reserved for ISA expansion cards

Enabled

Memory is reserved for ISA expansion cards

Internal Graphics Mode Select [Enable, 8MB]

The

Internal Graphic Mode Select

option determines the amount of system memory that

can be used by the Internal graphics device.

Disable

Enable, 1MB

1MB of memory used by internal graphics device

Enable, 8MB

EFAULT

8MB of memory used by internal graphics device

Summary of Contents for AFL-xxA-N270 series












































































































































































Search results

Summary of Contents for AFL-xxA-N270 series

Reviews:

IEI Technology AFL-xxA-N270 series, User Manual, Page: 114 / 171

Search results

Summary of Contents for AFL-xxA-N270 series

Reviews: