IEI Technology AFL-15A-N270 User Manual Download Page 91

Page: 91 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 91

BIOS Menu 10: Advanced Power Management Configuration

Restore on AC Power Loss [Last State]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.

Power Off

The system remains turned off

Power On

The system turns on

Last State

EFAULT

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Power Button Mode [On/Off]

Use the

Power Button Mode

BIOS to specify how the power button functions.

On/Off D

EFAULT

When the power button is pressed the system is either

turned on or off

Suspend

When the power button is pressed the system goes into

suspend mode

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands