IEI Technology AFL-15A-N270 User Manual Download Page 51

Page: 51 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 51

4.9.8.1 COM3 RS-422 and RS-485 Pinouts

The pinouts for RS-422 and RS-485 operation of external serial port COM 3 are detailed

below.

COM 3

RS-422 Description

Pin 1

TX-

Pin 2

TX+

Pin 6

RX-

Pin 7

RX+

Table 4-10: RS-422 Pinouts

COM 3

RS-485 Description

Pin 1

Data-

Pin 2

Data+

Table 4-11: RS-485 Pinouts

4.10 Mounting the System

WARNING!

When mounting the flat panel PC onto an arm, onto the wall or onto a

panel, it is better to have more than one person to help with the installation

to make sure the panel PC does not fall down and get damaged.

The four methods of mounting the AFOLUX AFL-15A-N270 are listed below.

Wall

mounting

Panel

mounting

Arm

mounting

Rack

mounting

The four mounting methods are described below.

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands