IEI Technology AFL-15A-N270 User Manual Download Page 111

Page: 111 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 111

7.1 Available Software Drivers

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

The following drivers can be installed on the system:

Chipset

VGA

Audio

LAN

Touch

screen

Wireless

Bluetooth

(Optional)

Installation instructions are given below.

7.2 Starting the Driver Program

To access the driver installation programs, please do the following.

Step 1:

Insert the CD-ROM that came with the system into a CD-ROM drive attached to

the system.

Step 2:

Click

AFL N270 Series

Step 3:

Select the

AFLMB2-945GSE-N270-R10 Driver

Step 4:

The list of drivers in

Figure 7-1

appears.

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

IEI Technology AFL-15A-N270, User Manual, Page: 111 / 158

Search results

Summary of Contents for AFL-15A-N270

Reviews: