IEI Technology AFL-15A-N270 User Manual Download Page 109

Page: 109 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 109

Discard Changes and Exit

Use the

Discard Changes and Exit

option to exit the BIOS configuration setup program

without saving the changes made to the system.

Discard Changes

Use the

Discard Changes

option to discard the changes and remain in the BIOS

configuration setup program.

Load Optimal Defaults

Use the

Load Optimal Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F9 key can be used for this operation.

Load Failsafe Defaults

Use the

Load Failsafe Defaults

option to load failsafe default values for each of the

parameters on the Setup menus.

F8 key can be used for this operation.

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands