IEC miniReStoramod Installation, Operation & Maintenance Manual Download Page 6

Page: 6 / 28

Modular Hi-Rise Replacement Series – MIY

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

SECTION ONE — Receipt, Unpacking, & Inspection, Cont’d.

Potential Unit Configurations

NOTE: Risers can not be installed on the Return Air side of the cabinet. (Front)

Figure 1. Air Arrangements

NOTES: 1. Risers pictued are shown for reference purposes only and adhere to the IEC

standard convention.

2. MRY/MIY equipment is designed to use existing risers, so risers are typically not

sold with these models.

3. Riser supply-return configurations and temperature should be labeled prior to

demolition, and must be verified prior to installation, as they may differ from the

IEC standard convention.

Single-side Supply

Sup

Ret

Sup

Ret

Sup

90°

Sup

Ret

Sup

90°

Sup

Ret

Sup

Ret

Sup

Ret

Sup

90°

Single-side and Top Supply

Top Supply Only

Sup

Ret

Supply

Ret

Sup

Ret

Sup

90°

Sup

Ret

Sup

Supply

90°

Sup

Ret

Sup

Ret

Sup

Ret

Supply

90°

Ret

Sup

Ret

Supply

Sup

90°

Sup

Ret

Supply

Ret

90°

Ret

Sup

Ret

Supply

Ret

90°

Rear

Riser Location

MOD

CABINET

Right

Front

Left

HR = Hot Water Return

HS = Hot Water Supply

D = Drain

CR = Cold Water Return

CS = Cold Water Supply

Summary of Contents for miniReStoramod





























Search results

Summary of Contents for miniReStoramod

Reviews:

IEC miniReStoramod, Installation, Operation & Maintenance Manual, Page: 6 / 28

Search results

Summary of Contents for miniReStoramod

Reviews: