background image

p.3

IMPORTANT SAFETY INSTRUCTIONS

1

IMPORTANT SAFETY INSTRUCTIONS

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6.

Clean only with dry cloth.

7.

Do not block any ventilation openings. Install in accordance with the manufacturer’s ins

tructions.

8.

Do not install near any heat sources such as radiators, heat registers, or other apparatus

(including amplifiers) that produce heat.

9.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two bla

des and a third grounding prong. The wide blade or the third prong is provided for you

r safety. If the provided plug does not fit into your outlet, consult an electrician for repla

cement of the obsolete outlet.

10.

Protect the power cord from being walked on or pinched particularly at plugs, convenie

nce receptacles, and the point where they exit from the apparatus.

11.

Only use attachments/accessories specified by the manufacturer.

12.

Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sol

d with the apparatus.

13.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparat

us combination to avoid injury from tip-over.

14.

Refer all servicing to qualified service personnel. Servicing is required when the apparat

us has been damaged in any way, such as power supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the apparatus has been expo

sed to rain or moisture, does not operate normally, or has been dropped.

Summary of Contents for iMDC-MAIN
















































































Reviews: