IDT Tsi578 User Manual Download | Manualshive

Page: 348 / 527

background image

12. Serial RapidIO Registers > IDT-Specific Performance Registers

348

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

12.9.8

RapidIO Port x Performance Statistics Counter 4 Register

This register is used to collect performance statistics. These counters provide the means of
accumulating statistics for the purposes of performance monitoring measurements: throughput and
latency.

The PS4_CTR counter collects performance statistics information based on the configuration fields
specified in the

“RapidIO Port x Performance Statistics Counter 4 and 5 Control Register” on

.

The PS4_CTR counter value is writable for testing purposes.This counter saturates when it reaches its
maximum value 0xFFFFFFFF and is cleared on a read. The PS4_CTR is enabled, when
PS4_PRIO[0..3] value in the

“RapidIO Port x Performance Statistics Counter 4 and 5 Control

Register” on page 340

) register is configured to a value other than 0.

Register name: SP{0..15}_PSC4

Reset value: 0x0000_0000

Register offset: 13050, 13150, 13250, 13350, 13450,

13550, 13650, 13750, 13850, 13950, 13A50,

13B50, 13C50, 13D50, 13E50, 13F50

Bits

0

1

2

3

4

5

6

7

00:7

PS4_CTR

8:15

PS4_CTR

16:23

PS4_CTR

24:31

PS4_CTR

Bits

Name

Description

Type

Reset

Value

0:31

PS4_CTR

This counter is used to collect performance statistics based on the
configurations specified through the

“RapidIO Port x Performance

Statistics Counter 4 and 5 Control Register” on page 340

A read clears this register.

R/W

0

«
...
346
347
348
349
350
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

SUPERSTACK 3 3226

Brand: 3Com Pages: 5

Brand: 3Com Pages: 139

CoreBuilder 7000

Brand: 3Com Pages: 150

CoreBuilder 7000

Brand: 3Com Pages: 264

Brand: 3Com Pages: 574

Brand: 3Com Pages: 333

SUPERSTACK 3 3226

Brand: 3Com Pages: 70

OfficeConnect 3C16790C

Brand: 3Com Pages: 18

Brand: 3Com Pages: 1314

SuperStack II Switch 1100

Brand: 3Com Pages: 62

Brand: AAVARA Pages: 23

Brand: Campbell Hausfeld Pages: 12

Brand: Maipu Pages: 21

Brand: Maico Pages: 56

Brand: ABB Pages: 10

Brand: Manhattan Pages: 2

Brand: Baxall Pages: 33

Brand: protech Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands