IDT Tsi578 User Manual Download | Manualshive

Page: 344 / 527

background image

12. Serial RapidIO Registers > IDT-Specific Performance Registers

344

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

12.9.4

RapidIO Port x Performance Statistics Counter 0 Register

This register is used to collect performance statistics. These counters provide the means of
accumulating statistics for the purposes of performance monitoring measurements: throughput and
latency.

The PS0_CTR counter collects performance statistics information based on the configuration fields
specified in the

“RapidIO Port x Performance Statistics Counter 0 and 1 Control Register” on

.

The PS0_CTR counter value is writable for testing purposes.This counter saturates when it reaches its
maximum value 0xFFFFFFFF and is cleared on a read. The PS0_CTR is enabled, when
PS0_PRIO[0..3] value in the

“RapidIO Port x Performance Statistics Counter 0 and 1 Control

Register” on page 332

is configured to a value other than 0.

Register name: SP{0..15}_PSC0

Reset value: 0x0000_0000

Register offset: 13040, 13140, 13240, 13340, 13440,

13540, 13640, 13740, 13840, 13940, 13A40,

13B40, 13C40, 13D40, 13E40, 13F40

Bits

0

1

2

3

4

5

6

7

00:7

PS0_CTR

8:15

PS0_CTR

16:23

PS0_CTR

24:31

PS0_CTR

Bits

Name

Description

Type

Reset

Value

0:31

PS0_CTR

This counter is used to collect performance statistics based on the
configurations specified through the

“RapidIO Port x Performance

Statistics Counter 0 and 1 Control Register” on page 332

A read clears this register.

R/W

0

«
...
342
343
344
345
346
...
»

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

DES-3224 - Switch

Brand: D-Link Pages: 75

Brand: DANLERS Pages: 2

Brand: Gefen Pages: 31

Brand: ORiNG Pages: 2

TIMEGUARD WF10COM

Brand: Theben Pages: 35

Brand: Holland Pages: 4

CN8000 KVM on the NET

Brand: ATEN Pages: 2

Brand: XtendLan Pages: 24

Brand: Lindy Pages: 2

Brand: Labgear Pages: 8

Brand: C&H Technologies Pages: 28

Brand: Fastcabling Pages: 4

Brand: SALZ Pages: 2

Brand: Broadcast Tools Pages: 10

MTX-CAT6-2IP-4X16

Brand: KVMSwitchTech Pages: 24

Brand: Lanpro Pages: 19

Brand: CYP Pages: 28

Brand: KinAn Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands