IDT TSI384 User Manual Download Page 214

Page: 214 / 281

14. Register Descriptions

214

Tsi384 User Manual
May 5, 2014

Integrated Device Technology

www.idt.com

14.8

Downstream Non-transparent Address Remapping

Registers

14.8.1

Secondary Bus Non-prefetchable Address Remap Control Register

Register offset: 0x0E4

Bits

31:24

SEC_NP_LBASE

23:16

SEC_NP_LBASE

Reserved

15:08

Reserved

IO_SIZE

07:00

Reserved

NP_REMA

PP_EN

Reserved

Bits

Name

Description

Type

Reset value

31:20

SEC_NP_LBASE

Secondary non-prefetchable lower base.

R/W

0x000

19:13

Reserved

Reserved.

0x00

12:8

IO_SIZE

This field describes how many upper bits of a downstream
I/O address are discarded.

R/W

0x00

7:4

Reserved

Reserved.

0x0

NP_REMAPP_EN

1 = Enable non-prefetchable address remapping

R/W

0x0

2:0

Reserved

Reserved.

0x0

Summary of Contents for TSI384


























































































































































































































































































Search results

Summary of Contents for TSI384

Reviews:

Related manuals for TSI384

Brands by name

Popular brands

IDT TSI384, User Manual

Search results

Summary of Contents for TSI384

Reviews:

Related manuals for TSI384

Brands by name

Popular brands