manualshive.com logo in svg

IDT 8A3 Series, Programming Manual

The IDT 8A3 Series programming manual is an essential resource for users seeking to maximize the functionality of their device. This comprehensive manual provides detailed instructions and guidelines for efficient programming, available for free download at manualshive.com. Unlock the full potential of your device with this user-friendly manual.

Share
Download
background image

278

©2018 Integrated Device Technology, Inc

September 12, 2018

8A3xxxx Family Programming Guide

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_1

Configure the fast lock disable delay.

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_2

Configure the output TDC .

TRIGGER: Writing to this byte triggers a read and activation in hardware of all the bytes of the OUTPUT_TDC_CFG module.

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_0 Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

FAST_LOCK_ENABLE_D

ELAY[15:0]

R/W

0

Duration to wait after enabling output TDC fast lock.  
Unsigned 16-bit value in microseconds.  0 = default 500 microseconds.
When output TDC is enabled, it needs time for the reference clock to settle to 
the correct frequency.  Fast lock is used to shorten the settling time to within 
microseconds compared to milliseconds.  

Table 374: OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_1 Bit Field Locations and Descriptions

Offset 

Address 

(Hex)

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_1 Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

002h

FAST_LOCK_DISABLE_DELAY[7:0]

003h

FAST_LOCK_DISABLE_DELAY[15:8]

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_1 Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

FAST_LOCK_DISABLE_D

ELAY[15:0]

R/W

0

Duration to wait after disabling fast lock to allow the output TDC reference clock 
time to settle.
Unsigned 16-bit value in microseconds.  0 = default 500 microseconds.
Fast lock is disabled prior to measurement and needs time to settle afterwards.

Table 375: OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_2 Bit Field Locations and Descriptions

Offset 

Address 

(Hex)

OUTPUT_TDC_CFG.OUTPUT_TDC_CFG_GBL_2 Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

004h

RESERVED[7:2]

REF_SEL[1]

ENABLE[0]

Summary of Contents for 8A3 Series





















































































































































































































































































































































Reviews:

No comments

Related manuals for 8A3 Series

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
T.A HALL 6370 Instruction Manual preview
HALL 6370
Brand: T.A Pages: 11
Datum bc635VME Operation And Technical Manual preview
bc635VME
Brand: Datum Pages: 49
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20
Clare Controls ClareVision CV-M161620-04 Installation Manual preview
ClareVision CV-M161620-04
Brand: Clare Controls Pages: 32
Jäger ADwin-light-16 Manual preview
ADwin-light-16
Brand: Jäger Pages: 54
Paradyne Application Module 9109 OCU-DP Installation Instructions Manual preview
Application Module 9109 OCU-DP
Brand: Paradyne Pages: 8
FiberHome AN5506-04 Series Product Manual preview
AN5506-04 Series
Brand: FiberHome Pages: 146
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2
ADTRAN OC-12 Manual preview
OC-12
Brand: ADTRAN Pages: 2
ADTRAN SFP Series Quick Start preview
SFP Series
Brand: ADTRAN Pages: 4
ADTRAN TRACER 4205 Quick Start Manual preview
TRACER 4205
Brand: ADTRAN Pages: 9
AT&T AC8200 Installation Manual preview
AC8200
Brand: AT&T Pages: 16
MSI TV Series User Manual preview
TV Series
Brand: MSI Pages: 90
Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W Series Specifications preview
Scalable Multi-Graphic Videowall Processors MGP 464W Series
Brand: Extron electronics Pages: 2
Renesas M38C29T-64LCA User Manual preview
M38C29T-64LCA
Brand: Renesas Pages: 6

Brands by name

Popular brands

Load more brands