IDT 8A3 Series Programming Manual Download Page 148 | Manualshive

Page: 148 / 340

background image

148

©2018 Integrated Device Technology, Inc

September 12, 2018

8A3xxxx Family Programming Guide

DPLL_0.DPLL_LOCK_0

Phase lock threshold.

DPLL_0.DPLL_LOCK_1

Phase lock monitor duration.

DPLL_0.DPLL_HO_CFG Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

RESERVED

N/A

-

This field must not be modified from the read value

HOLDOVER_MODE[2:0]

R/W

0

Holdover type configuration.
simple: holds DPLL with latest integrator value
manual: holds DPLL with value from
DPLL_CTRL_n.DPLL_MANUAL_HOLDOVER_VALUE
advanced: holds DPLL with value derived from filtered DPLL frequency history
0 = simple
1 = manual
2 = advanced

Table 182: DPLL_0.DPLL_LOCK_0 Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_0.DPLL_LOCK_0 Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

00Bh

PHASE_UNIT[7:6]

PHASE_LOCK_MAX_ERROR[5:0]

DPLL_0.DPLL_LOCK_0 Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

PHASE_UNIT[7:6]

R/W

0

Phase lock threshold unit.
0 = 1 ns
1 = 10 ns
2 = 100 ns
3 = 1 us

PHASE_LOCK_MAX_ERR

OR[5:0]

R/W

0

Phase lock threshold value.

Table 183: DPLL_0.DPLL_LOCK_1 Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_0.DPLL_LOCK_1 Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

00Ch

PHASE_MON_DUR[7:0]

«
...
146
147
148
149
150
...
»

Summary of Contents for 8A3 Series





















































































































































































































































































































































Reviews:

No comments

Related manuals for 8A3 Series

Brand: EAW Pages: 10

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

H3C S7500E Series

Brand: H3C Pages: 34

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: Intel Pages: 108

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: IDT Pages: 93

Brand: Kanguru Pages: 13

Brand: Lanner electronics Pages: 59

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

Brand: Intel Pages: 958

Brand: Acromag Pages: 23

Brand: Top Pages: 21

Brand: Hama Pages: 25

Brand: Accusys Pages: 34

Brand: Vega Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands