manualshive.com logo in svg

IDT 8A3 Series, Programming Manual

The IDT 8A3 Series programming manual is an essential resource for users seeking to maximize the functionality of their device. This comprehensive manual provides detailed instructions and guidelines for efficient programming, available for free download at manualshive.com. Unlock the full potential of your device with this user-friendly manual.

Share
Download
background image

123

©2018 Integrated Device Technology, Inc

September 12, 2018

8A3xxxx Family Programming Guide

SYS_APLL.SYS_APLL_CFG_2

Sets APLL configuration register 2.

PFD_RESET_CS[1]

R/W

0

Reset to 2.5V current steering PFD.
Reset must be high for 3.3V VDDA operation, low for 2.5V VDDA operation.

PFD_RESET_SS_1[0]

R/W

0

Reset to 3.3V source switching PFD #1.
Reset must be high for 2.5V VDDA operation, low for 3.3V VDDA operation.

Table 150: SYS_APLL.SYS_APLL_CFG_2 Bit Field Locations and Descriptions

Offset 

Address 

(Hex)

SYS_APLL.SYS_APLL_CFG_2 Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

003h

RESERVED[

7]

PFD_RESET

_SS_2[6]

CP_CS_500

U_ENABLE[5

]

CP_CS_250

U_ENABLE[4

]

CP_CS_125

U_ENABLE[3

]

CP_CS_CURRENT[2:0]

SYS_APLL.SYS_APLL_CFG_2 Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

RESERVED

N/A

-

This field must not be modified from the read value

PFD_RESET_SS_2[6]

R/W

0

Reset to 3.3V source switching PFD #2.
Reset must be high for 2.5V VDDA operation, low for 3.3V VDDA operation.

CP_CS_500U_ENABLE[5]

R/W

0

Enable current steering charge pump 500uA gain control.
Enable 500uA current source for cs charge pump. For use in 2.5V VDDA 
operation. 

CP_CS_250U_ENABLE[4]

R/W

0

Enable current steering charge pump 250uA gain control.
Enable 250uA current source for cs charge pump. For use in 2.5V VDDA 
operation

CP_CS_125U_ENABLE[3]

R/W

0

Enable current steering charge pump 125uA gain control.
Enable 125uA current source for cs charge pump. For use in 2.5V VDDA 
operation. 

CP_CS_CURRENT[2:0]

R/W

0

Control bias current for current steering charge pump.
Reference current for 2.5V VDDA operation. 125uA steps. 0 = 125uA, 7 = 
1000uA.

SYS_APLL.SYS_APLL_CFG_1 Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

Summary of Contents for 8A3 Series





















































































































































































































































































































































Reviews:

No comments

Related manuals for 8A3 Series

LevelOne FPC-0103T Manual preview
FPC-0103T
Brand: LevelOne Pages: 31
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
Eagle Technology PC104PLUS-26 User Manual preview
PC104PLUS-26
Brand: Eagle Technology Pages: 39
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Brand: Ebyte Pages: 23
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
audemat DIGIPLEXER 246 User Manual preview
DIGIPLEXER 246
Brand: audemat Pages: 93
Thecus N5200BR User Manual preview
N5200BR
Brand: Thecus Pages: 90
Silex technology Embedded Intelligent Module SX-560 Developer'S Reference Manual preview
Embedded Intelligent Module SX-560
Brand: Silex technology Pages: 110
artisan PB-SIO4A Manual preview
PB-SIO4A
Brand: artisan Pages: 36
Silicon Laboratories SiM3L1xx User Manual preview
SiM3L1xx
Brand: Silicon Laboratories Pages: 91
D-Link WCB-B11 User Manual preview
WCB-B11
Brand: D-Link Pages: 9

Brands by name

Popular brands

Load more brands