manualshive.com logo in svg

IDT 89HPES48T12G2, User Manual, Page: 185 / 276

Share
Download
IDT 89HPES48T12G2 User Manual Download Page 185

IDT   PCI to PCI Bridge and Proprietary Port Specific Registers

PES48T12G2 User Manual

15 - 11

April 5, 2013

PCI Express Capability Structure

PCIECAP - PCI Express Capability (0x040)

PCIEDCAP - PCI Express Device Capabilities (0x044)

Bit 

Field

Field

Name

Type

Default

Value

Description

7:0

CAPID

RO

0x10

Capability ID.

 The value of 0x10 identifies this capability as a PCI 

Express capability structure.

15:8

NXTPTR

RWL

Refer to sec-

tion Capabil-

ity Structures 

on page 14-3.

Next Pointer.

 This field contains a pointer to the next capability 

structure.

19:16

VER

RWL

0x2

PCI Express Capability Version.

 This field indicates the PCI-SIG 

defined PCI Express capability structure version number. 
The switch is compliant with the Express Capabilities Register 
Expansion ECN.

23:20

TYPE

RO

Upstream:

0x5

Downstream:

0x6

Port Type.

 This field identifies the type of switch port (upstream or 

downstream).

24

SLOT

RWL

0x0

Slot Implemented.

 This bit is set when the PCI Express link asso-

ciated with this Port is connected to a slot. This field does not apply 
to an upstream port and should be set to zero.

29:25

IMN

RO

0x0

Interrupt Message Number. 

The function is allocated only one 

MSI. Therefore, this field is set to zero.

31:30

Reserved

RO

0x0

Reserved field.

Bit 

Field

Field

Name

Type

Default

Value

Description

2:0

MPAYLOAD

RWL

0x4

Maximum Payload Size Supported.

 This field indicates the maxi-

mum payload size that the device can support for TLPs. 
0x0 - (s128) 128 bytes max payload size
0x1 - (s256) 256 bytes max payload size
0x2 - (s512) 512 bytes max payload size
0x3 - (s1024) 1024 bytes max payload size
0x4 - (s2048) 2048 bytes max payload size
0x5 - (s4096) 4096 bytes max payload size
0x6 - reserved (treated as 128 bytes)
0x7 - reserved (treated as 128 bytes)

4:3

PFS

RO

0x0

Phantom Functions Supported.

 This field indicates the support 

for unclaimed function number to extend the number of outstand-
ing transactions allowed by logically combining unclaimed function 
numbers. The value is hardwired to 0x0 to indicate that no function 
number bits are used for phantom functions.

5

ETAG

RWL

0x1

Extended Tag Field Support.

 This field indicates the maximum 

supported size of the Tag field as a requester.

Summary of Contents for 89HPES48T12G2





















































































































































































































































































Reviews:

No comments