IDT 89HPES16NT2 User Manual Download Page 166 | Manualshive

Page: 166 / 292

background image

IDT Non-Transparent Mode Operation

PES16NT2 User Manual

10 - 36

April 15, 2008

Notes

PC_PCIELSTS - Port C NTB Mode PCI Express Link Status (0x052)

PC_PCIESCAP - Port C NTB Mode PCI Express Slot Capabilities (0x054)

Bit

Field

Field

Name

Type

Default

Value

Description

3:0

LS

RO

0x1

Link Speed

. This field is hardwired to 2.5 Gbps.

9:4

LW

RO

HWINIT

Link Width

. This field indicates the negotiated width of the

link.

10

TERR

RO

0x0

Training Error.

When set, this bit indicates that a link train-

ing error has occurred.

11

LTRAIN

RO

0x0

Link Training

. When set, this bit indicates that link training

is in progress.

12

SCLK

RWL

HWINIT

Slot Clock Configuration

. When set, this bit indicates that

the component uses the same physical reference clock
that the platform provides. The initial value of this field is
the state of the CCLKUS signal for port A and the CCLKDS
signal for downstream ports B and C. The value contained
in Serial EEPROM may override these default values.

15:13

Reserved

RO

0x0

Reserved field.

Bit

Field

Field

Name

Type

Default

Value

Description

0

ABP

RO

0x0

Attention Button Present

. Hot-plug is not supported.

1

PCP

RO

0x0

Power Control Present

. Hot-plug is not supported.

2

MRLP

RO

0x0

MRL Sensor Present

. Hot-plug is not supported.

3

ATTIP

RO

0x0

Attention Indicator Present

. Hot-plug is not supported.

4

PWRIP

RO

0x0

Power Indicator Present

. Hot-plug is not supported.

5

HPS

RO

0x0

Hot Plug Surprise

. Hot-plug is not supported.

6

HPC

RO

0x0

Hot Plug Capable

. Hot-plug is not supported.

14:7

SPLV

RO

0x0

Slot Power Limit Value

. Feature not supported between

the Port C PCI-to-PCI bridge and the internal endpoint.

16:15

SPLS

RO

0x0

Slot Power Limit Scale

. Feature not supported between

the Port C PCI-to-PCI bridge and the internal endpoint.

17

EIP

RO

0x0

Electromechanical Interlock Present

. Hot-plug is not

supported.

18

NCCS

RO

0x0

No Command Completed Support

. Hot-plug is not sup-

ported.

31:19

PSLOTNUM

RWL

0x0

Physical Slot Number

. This field indicates the physical

slot number attached to this port. For devices intercon-
nected on the system board, this field should be initialized
to zero.
This bit is read-only and has a value of zero when the
SLOT bit in the PCIECAP register is cleared.

«
...
164
165
166
167
168
...
»

Summary of Contents for 89HPES16NT2





































































































































































































































































































Reviews:

No comments

Related manuals for 89HPES16NT2

Brand: Paradyne Pages: 86

Express Ethernetwork DI-704P

Brand: D-Link Pages: 2

Brand: Wave wifi Pages: 2

Brand: JB Systems Pages: 24

Brand: JB Systems Pages: 61

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: VCS Pages: 118

Brand: Gbord Pages: 8

Brand: Accton Technology Pages: 78

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: 8e6 Technologies Pages: 94

Brand: Cayman Systems Pages: 170

Brand: Stephen Pages: 8

Brand: Inter-m Pages: 20

Brand: Hamlet Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands