background image

2020-12-08 

 

                                                                                                                                            3

IDS NXT: Setup IDS NXT rome

1 Preface

Introduction

IDS Imaging Development Systems GmbH has taken every possible care in preparing this manual. We
however assume no liability for the content, completeness or quality of the information contained therein. The
content of this manual is regularly updated and adapted to reflect the current status of the software. We
furthermore do not guarantee that this product will function without errors, even if the stated specifications are
adhered to.

Under no circumstances can we guarantee that a particular objective can be achieved with the purchase of
this product.

Insofar as permitted under statutory regulations, we assume no liability for direct damage, indirect damage or
damages suffered by third parties resulting from the purchase of this product. In no event shall any liability
exceed the purchase price of the product.

Please note that the content of this manual is neither part of any previous or existing agreement, promise,
representation or legal relationship, nor an alteration or amendment thereof. All obligations of IDS Imaging
Development Systems GmbH result from the respective contract of sale, which also includes the complete and
exclusively applicable warranty regulations. These contractual warranty regulations are neither extended nor
limited by the information contained in this manual. Should you require further information on this product, or
encounter specific problems that are not discussed in sufficient detail in the manual, please contact your local
dealer or system installer.

Trademarks

The IDS logo is a registered trademark of IDS Imaging Development Systems GmbH,
registered for U.S. (Reg.No. 4,513,138) and other countries.

IDS NXT

 and 

uEye

 are registered trademarks of IDS Imaging Development Systems

GmbH. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.  All other
products or company names mentioned in this manual are used solely for purposes of identification or
description and may be trademarks or registered trademarks of the respective owners. 

Copyright

© IDS Imaging Development Systems GmbH. All rights reserved. This manual may not be reproduced,
transmitted or translated to another language, either as a whole or in parts, without the prior written permission
of IDS Imaging Development Systems GmbH.

Status: December 2020

Contact

Visit our web site 

http://www.ids-nxt.com

 where you will find all the latest information about our software and

hardware products. Please contact your local IDS distributors for first level support in your language. For a list
of IDS distributors worldwide please go to our website 

http://www.ids-nxt.com

.

Address

IDS Imaging Development Systems GmbH
Dimbacher Str. 6-8
D-74182 Obersulm, Germany

T

+49 7134 96196-0

E

[email protected]

W

http://www.ids-nxt.com

Summary of Contents for GS18031C-HQ























Reviews: