IDK MSD-72 Series Command Reference Manual Download

Page: 75 / 113

MSD-72 series Command Guide

@GCF / @SCF

RS-232C communication mode

Getting

Command

@GCF

Response

@GCF, mode_1, mode_2

Setting

Command

@SCF, port, mode

Response

@SCF, port, mode

Parameter

mode: Operation mode

mode_1: RS-232C CH1 operation mode

mode_2: RS-232C CH2 operation mode

0 = RECEIVER mode [Default], 1 = TRANSMITTER mode

port: RS-232C channel

0 = All channels,

1 = RS-232C CH1,

2 = RS-232C CH2

Getting

example

Command

Response

@GCF

@GCF,1,1

Description Getting the set operation modes of RS-232Cs.

TRANSMITTER mode

Setting

example

Command

Response

@SCF,1,1

Description Setting RS-232C CH1 to TRANSMITTER mode.

Remarks

These commands are only for RS-232C.

If IP address or RS-232C communication setting is changed, the communication

may be disabled. Change the environmental settings based on the MSD

settings.

3.3.12 LAN communication

@GIP / @SIP

IP address

Getting

Command

@GIP

Response

@GIP, unit_1, unit_2, unit_3, unit_4

Setting

Command

@SIP, unit_1, unit_2, unit_3, unit_4

Response

@SIP, unit_1, unit_2, unit_3, unit_4

Parameter

unit_1: Upper bit of the IP address to unit_4: lower bit of the IP address

0 to 255 = 8 bit (Decimal notation) [Default] 192.168.1.199

Getting

example

Command

Response

@GIP

@GIP,192,168,3,2

Description Getting the IP address of the MSD.

IP address:192.168.3.2

Setting

example

Command

Response

@SIP,192,168,3,2

Description Setting IP address to 192.168.3.2.

Remarks

If IP address or RS-232C communication setting is changed, the communication

may be disabled. Change the environmental settings based on the MSD

settings.

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands