IDK MSD-72 Series Command Reference Manual Download

Page: 7 / 113

MSD-72 series Command Guide

■

3-pin Terminal block RS-232C ports

Fix RS-232C cable to the attached 3-pin terminal block, and then connect it to the MSD.

AWG28 to AWG16 conductor gauge is recommended. The recommended wire strip length is 7 mm/0.28 inch.

If it is connected to a D-sub9 pin, cut RTS, CTS, DTR, and DSR (unused) as needed.

GND

RS-232C Tｘ

RS-232C Rx

GND

Up to 7 mm (0.28 inch approx.)

[Figure 2.2] Connecting RS-232C cable to 3-pin terminal block connector

2.1.2 RS-232C communication specification

[Table 2.2] RS-232C specification

Standard

RS-232C

Baud rate [bps]

4800 / 9600 / 19200 / 38400 [bps]

Data bit length [bit]

7 / 8

Parity check

NONE, EVEN, ODD

Stop bit [bit]

1 / 2

X parameter

Invalid

Flow control

None

Delimiter

CR LF (Carriage return and line feed, 0D and 0A in hex)

Communication method

Full duplex

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands