IDK MSD-72 Series Command Reference Manual Download

Page: 19 / 113

MSD-72 series Command Guide

3.3 Detailed descriptions

In this section, commands for MSD-7204UHD/MSD-7204UHDTB (4 outputs) are shown. For other models,

use each appropriate commands based on the number of outputs.

3.3.1 Error status

@ERR

Error status

Description

Response in case the command is not executed.

Response

@ERR, error

Parameter

error: Error status

1 = Erroneous parameter format or value

2 = Undefined command or wrong format

3 = Currently cannot be used.

4 = Not used.

5 = The command could not be executed, because the control command was not

registered.

6 = The command could not be processed since another command was being

executed.

7 = Automatic measurement of input timing failed.

8 = Loading EDID from the sink device failed.

9 = Not used.

10 = The control command was stopped according to the stop condition.

11 = The control command was stopped since the number of retries exceeded the

set value of “RETRY”.

12 = The control command of PJLink was stopped since the password did not

match.

13 = The image could not be captured since the image size to be captured

exceeded the reserved memory size.

14 = Capturing input image failed.

Getting example

Command @IOS

Response @ERR,2

@IOS is sent.

Command format error.

Remarks

－

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands