IDK MSD-72 Series Command Reference Manual Download

Page: 13 / 113

MSD-72 series Command Guide

3 Command

3.1 Command outline

A command consists of “@” (“40” in hexadecimal), 3 one-byte alphabetical characters (upper and lower
cases), and parameters (one-byte numbers

). For some commands, several parameters can be specified or

no parameter is required. Processing is executed by sending a delimiter at the end of the command.

Example: @SPM,2

“,”( a comma, “2C” in hexadecimal) is indicated between a command and parameter and between two
parameters.

: delimiter CR LF (line feed,

“0D” and “0A” in hex)

■

If there is an error:

An error command is returned if an undefined command or wrong parameter is included.

Example: @SOT,1

@ERR,1

■

Using as HELP:

If only delimiter is sent, command list as the help command is returned.

Example:

--------------- HELP (1/13) ---------------

(CHANNEL SELECT Command)

@SSW / @GSW : Set/Get Input Channel

@SSV / @GSV : Set/Get Video Input Channel

@SSA / @GSA : Set/Get Audio Input Channel

--------------- HELP (2/13) ---------------

(OUTPUT TIMING Command)

@SOT / @GOT / @GTD : Set/Get Output Timing

@SUM / @GUM : Set/Get Monitor Aspect

@SAP / @GAP : Set/Get Aspect

@SAR / @GAR : Set/Get Aspect Restore Mode

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands