IDK MSD-701UHD Command Reference Manual Download

Page: 29 / 115

MSD-701UHD / 702UHD / 801UHD/ 802UHD Command Guide

@GBC / @SBC

Background color

Getting

Command

@GBC, ch

Response

@GBC, ch, red, green, blue

Setting

Command

@SBC, ch_1, red_1, green_1, blue_1 (, ch_2, red_2, green_2, blue_2)

Response

@SBC, ch_1, red_1, green_1, blue_1 (, ch_2, red_2, green_2, blue_2)

Parameter

ch: Output channel

1 = OUT1, 2 = OUT2

ch_1-2: Output channel

0 = All outputs, 1 = OUT1, 2 = OUT2

red / red_1-2

: Background color (Red)

green / green_1-2 : Background color (Green)

blue / blue_1-2

: Background color (Blue)

0 to 255 [Default] 0 (Black)

Getting

example

Command

Response

@GBC,1

@GBC,1,128,128,128

Description Getting the set OUT1 background color.

RGB: 128 (Gray).

Setting

example

Command

Response

@SBC,1,128,128,128

Description Setting OUT1 background color to 128 (Gray) for all RGB.

Remarks

－

Summary of Contents for MSD-701UHD




















































































































Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands

IDK MSD-701UHD, Command Reference Manual

Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands