FDX-S Series User Guide
108
11.9 FDX-SIV4UT
Item
Description
Input
4 inputs
Video
HDBaseT
HDBaseT
HDCP 1.4/2.2
36 bit Deep Color, x.v.Color, 3D (*1), HDR (*2)
For WQHD, WQXGA, and 4K@24/25/30 (4:4:4)/50(4:2:0)/60 (4:2:0), Deep Color is not supported.
ARC/HEC/CEC are not supported.
EDID emulation, RS-232C, LAN
Format
VGA to 4K (Dot clock: 25 MHz to 600 MHz)
For WQHD/WQXGA, only Reduced Blanking is supported.
480i / 480p / 576i / 576p / 720p / 1080i / 1080p / 4K
For 4K format, 24 Hz/25 Hz/30 Hz/50Hz (4:2:0)/60 Hz (4:2:0) are supported.
Audio
Digital
Multi-channel LPCM up to 8 channels
Sampling frequency: 32 kHz to 192 kHz, Sample size: 16 bit to 24 bit
Reference level: -20 dBFS, Max. input level: 0 dBFS
Connector
RJ-45 (*3)
Cable
CAT.5E HDC, Cat5e UTP/STP, Cat6 UTP/STP (T568A/T568B straight-through)
Maximum transmission distances
328 ft. (100 m), 492 ft. (150 m) (Long reach mode is used) (*4)
General
Power consumption
About 31 Watts
Weight
1.1 lbs. (0.5 kg)
Temperature
Operating : 32°F to 104°F (0°C to +40°C)
Storage : -4°F to +176°F (-20°C to +80°C)
Humidity
Operating/Storage: 20% to 90% (Non Condensing)
*1
3D is supported if external EDID is selected while a 3D-supported sink device is connected for EDID setting or if copied EDID of 3D-supported sink device is selected for EDID
setting.
*2
HDR is supported if external EDID is selected while an HDR-supported sink device is connected for EDID setting or if copied EDID of an HDR-supported sink device is selected
for EDID setting.
*3
RJ-45 (HDBaseT connector) is only for extending digital
video and audio signals over a Cat5e/Cat6 cable. Use it with IDK’s HDBaseT Products. Do not use for LAN devices.
*4
The maximum transmission distance was obtained when IDK’s CAT.5E HDC cable was used. The distance may not be extended with some device combinations, cabling
method, or other manufacturer’s cable. Video may be disturbed or may not be output even if signals are within the range mentioned above.
The maximum transmission distance is the shorter distance of connected HDBaseT product or sink device’s maximum transmission distance.
Up to 492 ft. (150 m): 1080p (24 bit) in Long reach mode. For Long reach mode, use IDK’s HDBaseT Products that supports 328 ft. (100 m) or longer.
11.10 FDX-SOV4H
Item
Description
Output
4 outputs
Video
HDMI/DVI
HDMI/DVI 1.0
TMDS single link, HDCP 1.4
TMDS clock: 25 MHz to 300 MHz, TMDS data rata: 0.75 Gbps to 9 Gbps
36 bit Deep Color
x.v.Color/3D/ARC/HEC/CEC/HDR are not supported.
Format
VGA to 4K (Dot clock: 25 MHz to 300 MHz)
For WUXGA/QWXGA, only Reduced Blanking is supported.
480i / 480p / 576i / 576p / 720p / 1080i / 1080p / 4K
For 4K format, 24 Hz/25 Hz/30 Hz are supported.
Audio
Digital
Multi-channel LPCM up to 8 channels
Sampling frequency: 32 kHz to 192 kHz, Sample size: 16 bit to 24 bit
Reference level: -20 dBFS, Max. output level: 0 dBFS
Connector
Female HDMI Type A (19-pin)
Maximum transmission distances
98 ft. (30 m) (1080p@60), 66 ft. (20 m) (4K@30) (*1)
Functions
Anti-snow, Connection Reset (*2)
General
Power consumption
About 9 Watts
Weight
1.1 lbs. (0.5 kg)
Temperature
Operating : 32°F to 104°F (0°C to +40°C)
Storage : -4°F to +176°F (-20°C to +80°C)
Humidity
Operating/Storage: 20% to 90% (Non Condensing)
*1
The maximum cable distance varies depending on the connected devices and was measured under following conditions:
・
1080p@60 : When IDK
’s 24 AWG cable was used and signals of 1080p@60 24 bit/pixel (8 bit/component) was output.
・
4K@30 : When IDK
’s 24 AWG cable was used and signals of 4K@30 24 bit/pixel (8 bit/component) was output.
The maximum cable distance depends on the connected devi
ces. The distance may not be extended with some device combinations, cabling method, or other manufacturer’s
cable. Video may be disturbed or may not be output even if signals are within the range mentioned above.
*2
For digital systems, some problems, such as an HDCP authentication error, can often be recovered by physically disconnecting and reconnecting the digital cables. However,
the Connection Reset feature will fix these problems automatically without the need to physically plug and unplug the cables. It creates the same condition as if the cable were
physically disconnected and reconnected. This feature only works for the FDX-S
’s output. If other devices are connected between the FDX-S’s output and sink device, this
feature may be invalid.
