Idis DC-D1011 Operation Manual Download

Page: 33 / 54

Part 1 - Remote Setup

Settings

Select the

Settings

tab and configure recording

settings.

•

Recording Stream

: Choose a stream to use for

recording. It’s possible to designate different streams
for different recording modes.

Time-Lapse/Pre-Event

: Designate the stream to

use for recording in time lapse mode or event mode
(pre-event).

Event

: Designate the stream to use for recording in

event mode (post-event).

Preference

: Designate recording stream priority.

SD
Recording

Recording using the

Time-Lapse/

Pre-Event and Event

streams

designated above.

Network
Recording

Record from the remote program
using the designated recording
streams. If the remote program
does not support recording
streams, however,

Default

Recording Stream

specified

under

Video > Streaming

will

be used.

None

Record using the

SD Recording

stream or the

Network

Recording

stream, whichever has

the higher resolution.

•

Network Recording Failover

: Select a network

recording failover mode. You can recording video on
the SD card when recording from the remote program
fails. Video is recorded using the stream designated
under

Recording Stream > Event

Not supported if the recording mode under the

Schedule

tab is set to

Always

Time-Lapse

Summary of Contents for DC-D1011























































Search results

Summary of Contents for DC-D1011

Reviews:

Related manuals for DC-D1011

Brands by name

Popular brands

Idis DC-D1011, Operation Manual

Search results

Summary of Contents for DC-D1011

Reviews:

Related manuals for DC-D1011

Brands by name

Popular brands