IDEAL Bikes PRISMA-810 Original Instructions Manual Download

Page: 62 / 100

GEAR SHIFT SYSTEM

29 Hub shifting system

29.1 Method of operation

The hub shifting system is installed in the rear wheel hub and operated by using a twist-grip

shifter with a gear indicator on the right side of the handlebar.
The number of gears depends on the model.

29.2 Operating the hub shifting system

• To shift up or down a gear, turn the twist-grip shifter in the desired direction.
• If you have never used a hub shifting system or are unsure how to operate it, ask your

specialist dealer to show you how.

29.3 Checking the hub shifting system

• Check the components of the hub shifting system regularly to ensure that it continues

to operate correctly and to prevent unnecessary wear.

Make sure that the chain, chain rings and gear cables are undamaged.

Check the chain tension: The chain should not sag.

Lift the rear part of the pedelec so that you can move the rear wheel and turn the

pedals to set the rear wheel gently in motion.

Shift through all the gears: Shifting should be easy; there should be no blockages or

unusual noises.

• Contact your specialist dealer to:

replace any damaged or worn components on the hub shifting system and re-adjust

the hub shifting system again afterwards.

to check the hub shifting system and adjust it, if necessary, if you notice any irregu-

larities during the check.

Summary of Contents for PRISMA-810





































































































Search results

Summary of Contents for PRISMA-810

Reviews:

Related manuals for PRISMA-810

Brands by name

Popular brands

IDEAL Bikes PRISMA-810, Original Instructions Manual

Search results

Summary of Contents for PRISMA-810

Reviews:

Related manuals for PRISMA-810

Brands by name

Popular brands