manualshive.com logo in svg

ICT Hybrid Ultra ICT-2U4-DC12, Instruction Manual, Page: 59 / 97

Share
Download
ICT Hybrid Ultra ICT-2U4-DC12 Instruction Manual Download Page 59

Hybrid Ultra

 

 

855-350-050_Rev2.0_Instruction Manual 

                                               Page 

47

 of 84 

 

LVD Disconnect Voltage

: Shows the battery voltage when the LVD will 

disconnect the battery. 

 

LVD Reconnect Voltage

:  Shows the battery voltage when the LVD will 

reconnect the battery. 
 

LVD Status

:  Shows the status of the LVD (Open or Closed). 

 

Alarm Status

: Shows status of the batteries (Alarm or OK). 

 

4.5.2

 

SETTINGS & CONTOL 

This tab is used to adjust the settings of the BMMD. 
 

 

 

WARNING

 

Always consult battery manufacturer's specifications when 
selecting  battery  type.  Incorrect  battery  type  setting  may 
damage the battery

. If Lithium Ion type battery is selected, an 

integrated battery management system (BMS) must be used to 
protect  the  battery  cells  from  inappropriate  voltage  or  current 
levels. 
 
 
 
 
 
 
 
 
 
 

 

Configure Battery 

Battery  Type:

  Configure  the  Battery  Type  of  the  battery  used  in  the 

system (Lead Acid or Lithium Ion). 

 

Battery Capacity:

 Set the "Battery Capacity" in Ah (50 to 2000 Ah) of 

the total battery pack connected to the unit.  This value is used by the 
unit when estimated Run-time Remaining. The default setting is 100 Ah. 

 

Summary of Contents for Hybrid Ultra ICT-2U4-DC12


































































































Reviews:

No comments