ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 86

Page: 86 / 200

Parameter

Description

The snapshot of live interface.

Live Snapshot

The default path is
C:\Users\admin\WebDownload\LiveSnapsh
ot.

The recorded video of live interface.

Live Record

The default path is
C:\Users\admin\WebDownload\LiveRecord.

The snapshot of playback interface.

Playback Snapshot

The default path is
C:\Users\admin\WebDownload\PlaybackSna
pshot.

Admin in the path
refers to the account
being used.

The downloaded video of playback
interface.

Playback Download The default path is

C:\Users\admin\WebDownload\PlaybackRe
cord.

The clipped video of playback interface.

Video Clips

The default path is
C:\Users\admin\WebDownload\VideoClips.

Step 3

Click

Save

4.5.3 Audio

This section allows you to configure audio parameters and alarm audio.

4.5.3.1

Configuring Audio Parameter

This section includes audio parameters including: encode mode, sampling frequency, audio in type,
and noise filter.
Step 1

Select

Setting

Camera

Audio

Figure 4-70 Audio

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands