ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 49

Page: 49 / 200

Sound

Controls the sound during playback.

●

: Mute mode.

●

: Vocal state. You can adjust the sound.

Play control bar

Controls playback.

●

: Click the icon to play back recorded videos.

●

: Click the icon to stop playing back recorded

videos.

●

: Click the icon to play the next frame.

●

: Click the icon to slow down the playback.

●

: Click the icon to speed up the playback.

Progress bar

Displays the record type and the corresponding period.

●

Click any point in the colored area, and the
system will play back the recorded video from
the selected moment.

●

Each record type has its own color, and you can
see
their relations in

Record Type

bar.

Record/
Snapshot Type

Select the record type or snapshot type.

●

Record type includes

General

Event

Alarm

Manual

●

Snapshot type includes

General

Event

Alarm

Assistant

●

: You can zoom in or out video image of

the selected area through two operations.

●

: Click the icon to capture one picture of the

current video, and it will be saved to the
configured storage path.

Playback video

You can select the file type, data source, and record
date.

Video clip

Clip a certain recorded video and save it. For details,
see "4.4.3 Clipping Video".

Time format
progress bar

Includes 4 time formats: 30 minutes, 1 hour, 2 hour
and 24 hours.

4.4.2 Playing back Video or Picture

This section introduces the operation of video playback and picture playback. This section utilizes
video playback as an example.

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands