manualshive.com logo in svg

ICRealtime Edge IPEG-D20F-IRW3, User Manual, Page: 145 / 200

Share
Download
ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 145

Step 2

Set arming periods and alarm linkage action. For details, see "5.1.1 Alarm Linkage".

Step 3

Click

Save

.

Setting Intelligent Motion Detection

The IPC will trigger an event if a human, non-motorized vehicle, or motor vehicle appear on the
image. Enabling Intelligent Motion detection can avoid the false alarms triggered by the environment
changes. This function is enabled by default.

Prerequisites

●

Select

Setting

>

Event

>

Video Detection

>

Motion Detection

to enable the motion detection function.

●

You have set

Period

and

Area

in

Motion Detection

, with the sensitivity value larger than 0, and the

threshold value smaller than 100.

Procedure

Step 1

Select

Setting

>

Event

>

Intelligent Motion Detection

.

Figure 5-26 Intelligent Motion detection

133

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Reviews:

No comments