ICRealtime Edge IPEG-D20F-IRW3 User Manual Download Page 123

Page: 123 / 200

4.8.4.1

System Service

This section allows configuration of different services such as CGI ot ONVIF.
Step 1

Select

Setting

System

Safety

System Service

Figure 4-109 System service

Step 2

Enable the system service according as necessary.

Table 4-41 Description of system service parameters

Function

Description

SSH

Enables SSH authentication.

Multicast/Broadcast Search

When enabled, if multiple users are previewing the device
video image simultaneously through network, they can
scan to find your device with the multicast/broadcast
protocol.

Password Reset

Manage system security with this function.

Function

Description

CGI Service

Enables the common gateway interface services.

Onvif Service

Enables the ONVIF protocol.

Genetec Service

Enables the appropriate services.

Audio and Video
Transmission
Encryption

Enable to encrypt audio/video transmission.

If enabled, this may affect live viewing through applications.

111

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands

ICRealtime Edge IPEG-D20F-IRW3, User Manual

Search results

Summary of Contents for Edge IPEG-D20F-IRW3

Reviews:

Related manuals for Edge IPEG-D20F-IRW3

Brands by name

Popular brands