background image

INSTALLATION INSTRUCTIONS

R

410A Split System Air Conditioner

4

421 01 5104 02

Specifications subject to change without notice.

Table 1 

 Accessory Usage

Accessory

REQUIRED FOR LOW

AMBIENT

COOLING APPLICATIONS

(Below 55

5

F / 12.8

5

C)

REQUIRED FOR LONG LINE 

APPLICATIONS* (Over 80 ft. / 24.38 m)

Crankcase Heater

Yes

Yes

Compressor Start Assist Capacitor and Relay

Yes

Yes

Evaporator Freeze Thermostat

Yes

No

Liquid Line Solenoid Valve

No

See Long Line Applications Guideline

Low

ambient Pressure Switch

Yes

No

Support Feet

Recommended

No

Thermal Expansion Valve (TXV)
Hard Shutoff

Yes

Yes

Winter Start Control

Yes

No

* For tubing line sets between 80 and 200 ft. (24.38 and 60.96 m)  and/or 20 ft. (6.09 m) vertical differential, refer to Long Line Applications Guideline.

Table 2 

 Refrigerant Connections and Recommended Liquid and Vapor Tube Diameters (In.)

UNIT SIZE

LIQUID

RATED VAPOR 

up to 80 ft. (24.38 m)*

Connection and Tube

Diameter

Connection

Diameter

Rated Tube

Diameter

18, 24, 30,

3/8

3/4

3/4

36, 42, 48

3/8

7/8

7/8

60

3/8

7/8

1

1/8

* Units are rated with 25 ft. (7.6 m) of lineset.  See Specification sheet for performance data when using different size and length linesets.

Notes

:

1. Do not apply capillary tube or fixed orifice indoor coils to these units.
2. For Tubing Set lengths between 80 and 200 ft. (24.38 and 60.96 m) horizontal or 35 ft. (10.7 m) vertical differential 250 ft. (76.2 m) Total Equivalent Length), 

refer to the Long Line Applications Guideline.

Summary of Contents for CSA6
















Reviews: