ICP DAS USA tM-TH8 User Manual Download Page 124

Page: 124 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

124

tM-TH8

3.6.8 Sub-function 37 (0x25) Read channel
enabled/disabled status

This sub-function code is used to read the enabled/disabled status
of each channel in a module.

Request

Address

1 Byte

1 to 247

Function code

1 Byte

0x46

Sub function code 1 Byte

0x25

Response

Address

1 Byte

1 to 247

Function code

1 Byte

0x46

Sub function code 1 Byte

0x25

Enabled/disabled
status

1 Byte

0x00 ~ 0xFF, enabled/disabled
status of each channel, where bit 0
corresponds to channel 0, bit 1
corresponds to channel 1, etc.
When the bit is 1 it denotes that
the channel is enabled and 0
denotes that the channel is
disabled.

Error Response

Address

1 Byte

1 to 247

Function code

1 Byte

0xC6

Exception code

1 Byte

03: incorrect number of bytes

received

Summary of Contents for tM-TH8













































































































































Search results

Summary of Contents for tM-TH8

Reviews:

Brands by name

Popular brands

ICP DAS USA tM-TH8, User Manual

Search results

Summary of Contents for tM-TH8

Reviews:

Brands by name

Popular brands