background image

 

 

PROFI-5053  PROFIBUS DAQ Module - QuickStart (Apr/2017)  

ICP DAS USA, Inc.

 | 

www.icpdas-usa.com

 | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

 

 

PROFI-5053 

PROFIBUS Remote I/O Module 

Quick Start Guide

 

 

 

Introduction 

 

This user guide introduces the user how to implement the PROFI-5000 

into their applications in a quick and easy way. Therefore, it only provides 
the basic instructions. For more detail information about the PROFI -5000 
module, please refer to the PROFI-5000 user manual in the ICP DAS 
product CD or download it from ICP DAS web site. 

 

 

PROFI-5000 Connector and Pin Assignment 

 
 

Pin No. 

Signal 

Meaning 

B-Line 

Receive/Transmit data – plus 

GND 

Power ground of active terminator 

VP 

Power 5 volt of active terminator 

A-Line 

Receive/Transmit data - minus 

 

 

The PROFIBUS connector is a standard 9 -pin D-Sub connector, there are 
only 4 pins used in PROFI-5000. The pins VP and GND support the 5 volt 
power to active terminal resistor, and the A-Line and B-Line is the data bus. 

 

 

Status Indicator

 

 

 

PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-
5052/ PROFI-5053/ PROFI-5055/ PROFI-5060

 

 

It provides two types of status indicator, they are PWR 

 

LED (Red) and RUN LED (Green). 
 

Status Indicator 

 

Meaning 

 

Recommend solution 

PWR ON 

 

Master not Ready, 

1. Check the address setting 

 

Address not Match 

of module and DP-master. 

RUN OFF 

 

or 

2. Sets the DP-Master to 

 

 

Cfg Fault 

 

operation mode. 

 

   

3. Make sure of the 

 

   

 

consistency of Module 

 

   

 

Selection. 

Summary of Contents for PROFI-5000










Reviews: