manualshive.com logo in svg

ICP DAS USA CAN-Logger Series, User Manual, Page: 22 / 45

Share
Download
ICP DAS USA CAN-Logger Series User Manual Download Page 22

4.3.  Start to use CAN-Logger Utility tool 

 

Figure 4-2 Main frame of the CAN-Logger Utility tool 

 

A  Menu tool bar. User can change the Utility communication mode between “Online” 

and “Offline” on the “File” item and get the Utility version information on the “Help” 
item. “Online” mode is used for user to transmit/receive CAN messages to the 
connected module and monitor the CAN Bus status. “Offline” mode is used for 
display the logged data on the module SD card. 

 
B  Transmit/Receive frame. When using “Online” mode, this field will be divided into 

two parts after connect with module. One is used for display received CAN 
messages and the other is used for transmit CAN messages. When using “Offline” 
mode, this field is used for display the logged datas which are saved in the SD card. 
In this mode, user needs to use a SD card reader to get the SD data file. 

 
C  Scanned module information. On this frame, user can re-scan the new inserted 

module, configure the selected module and connect with the selected module. 

 
D  CAN Bus status frame. After connecting with module, user can get the CAN Bus 

status information on this frame. 

CAN-Logger series CAN Bus data logger devices User Manual (version 1.0.1)   

 

 

Page: 22

 

 

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]

 

 

Summary of Contents for CAN-Logger Series














































Reviews:

No comments