background image

1

PART #

DESCRIPTION

58747C

10-UP FJ/4RNR/10-UP GX EXT TRAVEL 2.5 

VS RR CDCV COILOVER KIT

58747C/58747C-700 INSTALLATION INSTRUCTIONS

WARNING!

** READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH 

BEFORE BEGINNING INSTALLATION! IF THESE INSTRUCTIONS ARE 

NOT PROPERLY FOLLOWED SEVERE FRAME, SUSPENSION AND TIRE 

DAMAGE MAY RESULT TO THE VEHICLE!

** ICON VEHICLE DYNAMICS RECOMMENDS THAT YOU EXERCISE 

EXTREME CAUTION WHEN WORKING UNDER A VEHICLE THAT IS 

SUPPORTED WITH JACK STANDS.

**ICON VEHICLE DYNAMICS RECOMMENDS ALL INSTALLATION TO 

BE PERFORMED BY A PROFESSIONAL SHOP/SERVICE TECHNICIAN. 

PRODUCT FAILURE CAUSED BY IMPROPER INSTALLATION WILL NOT BE 

COVERED UNDER ICON’S WARRANTY POLICY. 

1. 

If your vehicle is equipped with Kinetik Dynamic Suspension System (KDSS), deactivate the system before performing ANY work 

to the vehicle. Refer to the factory service manual for information on how to deactivate this system. KDSS will need to be reactivated 

once the installation is complete.

2. 

Using a properly rated jack, raise the front of the vehicle and support the frame rails with jack stands. Ensure the jack stands are 

secure and set properly before lowering the jack. NEVER WORK UNDER AN UNSUPPORTED VEHICLE. Remove the front wheels.

3. 

Disconnect the outer tie rod end on both sides. Remove the cotter pin and loosen the nut until it is flush with the end of the 

threads. Strike the end of the steering knuckle arm with a large hammer to dislodge the taper. Remove the nut and swing the tie rod 

out of the way.

COMPONENTS INCLUDED

(1) 154004 05+ TACO / FJ RESI MOUNT (PASS)

(1) 154005 05+ TACO / FJ RESI MOUNT (DRVR)

(1) 154953CD 07+ FJ/03+ 4RUNNER EXT TRAVEL 

CO RR CDCV (DRVR)

(1) 154953CP 07+ FJ/03+ 4RUNNER EXT TRAVEL 

CO RR CDCV (PASS)

(4) 605144 3/8-12 X .750 FLANGED SELF TAP 

BOLTS

(1) 611019 COILOVER HARDWARE KIT (PAIR)

(1) 611031 10+ SWAYBAR RELOCATION KIT

(1) 611051 HOSE CLAMP KIT

HARDWARE INCLUDED

611019 HARDWARE KIT

(6) 605101 3/8-16 X 1.000 BOLT

(6) 605131 3/8” SPLIT LOCK WASHER

611031 HARDWARE KIT

(2) 157110 10+ SWAYBAR BRACKET

(14) 605432 9/16 WASHER THICK 1.18 X .585 X .18

(4) 605100 3/8-16 X .750 BOLT

(4) 605133 3/8” FLAT WASHER

(4) 605808 M10-1.25 X 25MM

(2) 605853 M10-1.25 X 25MM FLANGED BOLT

611051 HARDWARE KIT

(4) STAINLESS STEEL HOSE CLAMP

TOOLS REQUIRED

JACK

JACK STANDS

TORQUE WRENCH

HAMMER

DRILL (KDSS ONLY)

11/32” DRILL BIT (KDSS ONLY)

5/16” NUT DRIVER

9/16” SOCKET / WRENCH

ANGLE GRINDER (KDSS ONLY)

8MM ALLEN WRENCH

10MM SOCKET / WRENCH

13MM SOCKET / WRENCH

14MM SOCKET / WRENCH

15MM SOCKET / WRENCH

18MM SOCKET / WRENCH

21MM SOCKET / WRENCH

TECH NOTES

1. YOUR ICON COILOVER ASSEMBLIES COME FACTORY CHARGED TO 150 PSI. RELEASING NITROGEN 

PRESSURE MAY LEAD TO SHOCK MALFUNCTION AND REDUCED RIDE QUALITY. FAILURE CAUSED BY 

LOW NITROGEN PRESSURE IS NOT COVERED UNDER ICON’S WARRANTY POLICY.

2. YOUR ICON COILOVER ASSEMBLIES COME SHIPPED AT ICON’S RECOMMENDED RIDE HEIGHT. DO 

NOT PRELOAD THE COIL BEYOND 2.13” (1.13” FOR 700LB COIL #158508) OF EXPOSED THREADS 

BETWEEN THE BOTTOM OF THE TOP CAP AND THE TOP OF THE COIL ADJUSTER NUT. A REDUCTION 

IN RIDE QUALITY WILL BE EXPERIENCED IF COILOVERS ARE ADJUSTED TO ALLOW FOR LESS THAN 

2” OF DROOP TRAVEL FROM STATIC RIDE HEIGHT.

3. KDSS EQUIPPED VEHICLES WILL REQUIRE THE SYSTEM TO BE DEACTIVATED BEFORE 

INSTALLATION, AND REACTIVATED AFTER INSTALLATION IS COMPLETE. REFER TO FACTORY 

SERVICE MANUAL FOR MORE INFORMATION.

4. KDSS EQUIPPED VEHICLES WILL NOT USE SWAYBAR RELOCATION KIT (611031).

5. REQUIRES USE OF ICON TUBULAR UPPER CONTROL ARM (58451) OR ICON BILLET UPPER 

CONTROL ARM (58551).

2-17-2020 REV.D

 INSTALLATION

7929 Lincoln Ave.  Riverside, CA 92504

Phone: 951.689.ICON | Fax: 951.689.1016

Reviews: