background image

 

 

Figure 2: TMA-011 LV and 
MV radar connector - Weipu 
SP1712/P9

 

Figure 3: TMA-011 HV 
radar connector - Weipu 
SP2112/P7 

CABLING 

 CAUTION: positive security/fail safe relays - contacts given for powered radar. 

 

 

 

HV 

(100-240 VAC)

 

PIN nr 

Color 

Function 

BLUE

 

~ Power Supply 

 

BROWN

 

~ Power Supply

 

YELLOW

/GREEN

 

EARTH 

WHITE 

Relay - COM

 

GREY

 

Relay - NO

 

YELLOW

 

Relay - NC

 

PURPLE

 

Do not connect

 

 
USER’S OUTPUTS  
Resistive load: 30 V AC 0.3 A - 60 V DC 0.3 A 
Option 250 V relay: 250 V AC - 30 V DC – 0.3 A 
 
REMARKS 

 

Make sure the plug is fully inserted in the socket and the cap is firmly tightened on the socket. 

 

Please disconnect the radar from power before maintenance intervention. 

 

 

LV 

(12-60 VDC – 10-30 VAC) 

& MV 

(21-75 VDC – 15-54 VAC)

 

PIN nr 

Color 

Function 

RED

 

Power ~ (AC), + (DC)

 

BLUE

 

Do not connect

 

BLACK  

Power ~(AC), - (DC GND) 

BROWN

 

Do not connect 

WHITE or 

PURPLE

  Relay - COM

 

GREY

 

Relay - NO

 

YELLOW 

Relay - NC

 

GREEN

 

Do not connect

 t 

PINK 

or

 

ORANGE

  Do not connect

 

Summary of Contents for TMA-011












Reviews: