INSTALLATION
ASSEMBLE THE UNIT
• Install the UR-FR5100 or UR-FR6100
(channel extension module)
q
Attach the supplied angles to both sides of the
channel extension module, and tighten the 2 sup-
plied screws (M4
×
8) on each side.
w
Install the channel extension module using the sup-
plied screws (Tapping screws: M3
×
8, Set screws:
M3
×
6) as shown below.
• Connect the control cable
q
Connect the supplied control cable to J502 on the
front board as shown below.
w
Cut the rubber caps of the control cables, then in-
sert the rubber caps to the front panel’s chassis as
shown below.
Set screws
Tapping
screws
Channel module
(original)
Channel extention
module
Set screws
Tapping
screws
Channel module
(original)
Channel extention
module
J502
q
w
J502
q
w
q
Replace the rubber seal and shielding plate of the
front panel, then tighten the 6 screws.
• Make sure the rubber seal is properly seated in the
groove of the chassis.
•
Be sure to match the correct positions of the holes of
the shielding plate and projections of the front panel’s
chassis.
w
Connect the control cables to the channel modules.
e
Return the front panel, top cover and screws to
their original positions.
Rubber seal
Holes
Projections
Rubber seal
Holes
Projections
P0
P1
P2
P3
P4
Shorter cable
(lower side)
Longer cable
(upper side)
Channel module
(original)
Channel extention module
P0
P1
P2
P3
P4
Shorter cable
(lower side)
Longer cable
(upper side)
Channel module
(original)
Channel extention module
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
Icom, Icom Inc. and the
logo are registered trademarks of Icom Incor-
porated (Japan) in the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
All other products or brands are registered trademarks or trademarks of
their respective holders.
INSTRUCTIONS
CHANNEL EXTENSION MODULES
Thank you for purchasing the UR-FR5100/
UR-FR6100
CHANNEL EXTENSION MODULES
.
Please read these instructions and repeater’s
instruction manual carefully before installation and
operation.
q
DC power cable ...................................................1
w
Control cable ........................................................1
e
Angles ..................................................................2
r
Screws (M4
×
8 mm) ..............................................4
t
Set screws (M3
×
6 mm) ........................................4
y
Tapping screws (M3
×
8 mm) .................................2
q
Remove 7 screws from top and 2 screws each
from both sides of the repeater, then slide off the
top cover to the direction of the arrow as illustration
below.
w
Remove 3 screws from bottom and 2 screws each
from both sides of the repeater.
e
Disconnect the control cable from the channel
module (original), then remove the front panel.
r
Remove 6 screws from the front panel, then re-
move the shielding plate and rubber seal.
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
P0
P1
P2
P3
P4
Channel module
(original)
Front panel
P0
P1
P2
P3
P4
Channel module
(original)
Front panel
Rubber seal
Shielding plate
Rubber seal
Shielding plate
SUPPLIED ACCESSORIES
OPENING CASE
w
e
y
t
q
r
UR-FR5100
UR-FR6100
