![background image](http://html2.mh-extra.com/html/icom/ic-f29sr/ic-f29sr_operating-instructions-manual_4224784011.webp)
4
SETTINGS
9
DTCS code setting
D
This transceiver is equipped with 84 DTCS codes.
DTCS operation enables silent standby, since you will
only receive calls from group members using the same
DTCS code.
Rotate
q
[VOL]
to turn OFF the power.
Set
w
[ROTARY SELECTOR]
to any channel other
than Channel 16.
While holding down
e
[PTT]
,
[Upper]
, and
[Lower]
,
rotate
[VOL]
to turn ON the power.
Rotate
r
[ROTARY SELECTOR]
to select the desired
channel (1 to 16) that you want to assign the DTCS
code to.
Hold down
t
[Lower]
until two beeps sound.
• The transceiver enters the DTCS code setting mode.
Push
y
[PTT]
the necessary number of times to en-
ter the ten’s digit of the desired DTCS code number
(grey column) as shown in the list below.
Push
u
[Upper]
.
• The selected number will be announced.
Push
i
[PTT]
the necessary number of times to en-
ter the one’s digit of the desired DTCS code number
(grey column) as shown in the list below.
Push
o
[Upper]
.
• The selected number will be announced.
!0
If you want to use Inverse mode, push
[PTT]
again.
• If you want to use Normal mode, skip this step.
!1
Push [Upper] to complete the setting.
!2
Turn OFF the power to exit the DTCS Code Setting
mode.
NOTE:
• If you make a mistake, go back to step
q
and follow
all the steps again.
• If you want to enter “0”, do not push
[PTT]
in step
t
and
u
, just push
[Upper]
. Then “zero” will be
announced. To turn OFF the DTCS code, enter “0.”
[Example]:
DTCS code No. 16 (114) Inverse mode as-
signment to channel 5
Rotate
q
[VOL]
to turn OFF the power.
While holding down
w
[PTT]
,
[Upper]
, and
[Lower]
,
rotate
[VOL]
to turn ON the power.
• The transceiver enters DTCS Code Setting mode.
Rotate
e
[ROTARY SELECTOR]
to select channel 5,
then hold down
[Lower]
until two beeps sounds.
Push
r
[PTT]
one time to enter “1” (the ten's digit) of
the number 16.
Push
t
[Upper]
.
• “One” will be announced.
Push
y
[PTT]
six times to enter “6” (the one’s digit) of
the number 16.
Push
u
[Upper]
.
• “Six” will be announced.
Push
i
[PTT]
again, to use Inverse mode.
Push
o
[Upper]
to complete the setting.
!0
Turn OFF the power to set the DTCS code.
• Available DTCS code list
No. Code No. Code No. Code No. Code No. Code
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
023
025
026
031
032
036
043
047
051
054
065
071
072
073
074
114
115
116
125
131
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
251
261
263
265
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
81
82
83
84
00
732
734
743
754
OFF
[ROTARY SELECTOR]
[VOL]
[Lower]
[Upper]
[PTT]
Setting the group code number (Continued)