background image

4

SETTINGS

8

Setting the beep and announcement level

2

5

4

3

1

5 (Linked)

4 (Linked)

3 (Linked)

2 (Linked)

1 (Linked)

Pushing

[Upper]

You can adjust the beep and announcement level 

between 1 and 5, or 1 (linked) and 5 (linked). When 

a linked option is selected, the beep audio level is 

adjustable by rotating [VOL].

1.  Rotate [VOL] to turn OFF the transceiver.

2.   Set [Rotary Selector] to any channel other than 

Channel 16.

3.   While holding down [Lower], rotate [VOL] to turn 

ON the transceiver and enter the Beep Level 

Adjustment mode.

 • An opening beep sounds and the selected channel 

number will be announced.

4.   Push [Upper] to change the beep level.

 

• A beep sounds every time you push [Upper]. 

Therefore, you can determine the current level setting 

by the increasing loudness of the beep that sounds.

 Infoomation

L

 •The adjustable range is 1 to 5 or 1 (Linked) to 5 

(Linked).

 •

Repeatedly pushing [Upper] first selects 1 (lowest) to 

5 (highest), and then selects the lowest linked level, 

1 (Linked) to the highest, 5 (Linked). Repeatedly 

pushing [Upper] repeats the cycle. See the illustration 

to the right.

 •To determine if you have selected a linked level, set 

[VOL] to minimum, then push [Upper] repeatedly, 

listening for the loudest beep (level 5). Pushing 

[Upper] once after the loudest beep will select 1 

(Linked). Repeatedly push [Upper] to select the 
desired linked level.

5.   Rotate [VOL] to turn OFF the transceiver and exit 

the Beep Level Adjustment mode.

NOTE:

Turn ON the Beep function (p. 7) before 

you start setting the beep and announcement level.

[Rotary Selector]

[VOL]

[Lower]

[Upper]

Previous view

Summary of Contents for IC-F29DR2























Reviews: